Відео

Amigo tengo uno d ese d los mismos pero n m quiere prender lo prove directo a ver si era el botón pero nada ns si m podías dar alguna indicación para poderlo reparar le agradezco

Amazing❤👍🇮🇩

use gloves

Oooooohhhh Asbestos warning light came on as I read the title and imma finish watching it

Oh my goodness, where DO i start!! First off.....please PLEASE use GLOVES and a FACE/MOUTH/NOSE covering/s when dealing with any VINTAGE or OLDER small engines using this type of Gasket material, as the risk of ASBESTOS type material is MUCH GREATER than today's type of material's, so you MUST KEEP AND STAY SAFE with this particular type of item ALONE!! 2ND.....I've no objection to your use of petrol to clean parts, i use old and '''out of date''' petrol/diesel regularly to clean parts on my chainsaw/mower/grass strimmer, as i have no access to a parts cleaner, and cannot afford one, but--(AGAIN!)--please, PLEASE use GLOVES and a MOUTH/NOSE/FACE covering when using LIQUID PETROLEUM PRODUCTS, such as petrol OR diesel, AND.....DISPOSE OF YOUR said products CAREFULLY/RESPONSABLY/SAFELY.....YOUR SAFETY FIRST.....ALWAY'S!! OK.....now for the shitty bits!! PLEASE try to use the proper tool for the job?: A pair of steel/metal Pliers is NOT the tool for undoing BRASS NUTS, or BRASS NUTS AND BOLTS, or SCREWS!! The correct tool for that type of operation is a SPANNER, or a RING SPANNER, used SLOWLY, with the addition--(if needed)--of a little WD40, or a little light oil like 3in1, or some heat used beforehand, to loosen stuck brass items like brass nut/bolts or screws. Brass, like Copper, is a soft metal and both do not do well when using steel or other metals against them IN FORCE. As to your ''lapping'' of the valve stems and seats, i feel you should have worked a little more on the exhaust valve seat, as that seat looked to be the most particularly pitted/corroded. Also, you used FAR too much lapping compound on both seats and valves.....most people use just the ''fine'' compound to lap valves with, but in your case i could see the reason why you used the coarse compound for the exhaust seat.....it really needed it, but still, it was too much.....''Less is More'', as they say nowaday's!?! I am so sorry to be going on, it is not you personaly Alex B, ok!?! The main shaft should of been taken out, the bearings/shaft should of been checked for alighment/wear, also the bearing shells for wear, as well as the cam followers too, and the piston body, the gudgeon--(WRIST PIN, for the Americas!!)--pin, and asociated rings. (In fact, the whole of the insides of the engine should have been torn apart, cleaned and checked for any wear/damage to any part, and then cleaned thoroughly, and then TORQUED TO SPEC in my humble opinion, which doesn't count for much and never did as far as i know anyway!) Next, TORQUE WRENCH SETTINGS/USAGE!!! ALEX, you really MUST get yourself a cheap TORQUE WRENCH for the bolts and nuts that you have to tighten to specification on your next rebuilds and restorations of small engines and the like! It really is NOT ENOUGH that you, or other people, just ''torque'' nuts and bolts down with power tools, (or, in some cases, using a ''breaker bar'' and some ''force''!!). ''TORQUING'' nuts and bolts should be done AS TO THE MANUFACTURERS SPECIFICATIONS, many of which can be found for any particular model, quite readily online, GOOGLE for one! ALEX.....I thank you for your time in reading this, as i do other contributors to your channel who may also have left a comment, or read this, my diatribe!! It is in the hope that you can ''pick up'' not just my little ''hints and tips'', but also other peoples hints, tips and advise too. The ''small engine community'' is growing, and YOU, a main contributor, should be growing with it. PLEASE, remember what i have said, ALWAYS with regards to YOUR safety, and the SAFETY of others, and PLEASE,remember what other, like minded small engine enthusiasts have said with regards to your channel Kind regards from MIKKY, FROM NORTH EAST SCOTLAND!! (On his wifes computer.....Shsss!!!)

Great job, and video "Alex B". I bought one in 2012, with two batteries and charger, but OEM version (no box and case). Batteries are dead about 7 years ago, but I rebuilt and sold that another drill. I use this drill with newer version higher capacity batteries (4 AH & 5AH batteries). My father is destroyed its chuck, I replaced it a metal drill chuck from AliExpress, and works fine. I checked it on Bosch services online page, but it has got a high price for me (~41.1USD). As they say in Hungary, the material is still in it.

I don't think you are supposed to oil the outer face of a sealed roller bearing nor the inner one for that matter... This part is not supposed to spin. If you want to oil the bearing - try injecting grease inside the bearing or just replace it.

Hi Alex. Please forgive my digging up this thread, but I happen to have exactly the same model, which unfortunately developed an electrical fault for which I have no parts list, let alone circuit diagram. I was wondering whether you might be willing to help me source a parts list or troubleshoot the fault please?

😢

This was my also childhood bicycle. This models was selling as name Pinokyo (Pinocchio) in Türkiye. Our friendship had to end when it's fork had broken. And there was a saddle bag on it.

👌🏾 very use full,,,

That lamp is a fairly recent Hong Kong or China-made. It would have made sense to simply buy a new globe.

Cool you went through this effort!

You did a great job looks real nice.

I have one of these and it's a turd--I bought it cheap for a job and promised I'd restore it once the job was finished. It's finally time to get down to it, so cheers for this one Alex.

Ese es el que tengo yo igualito azul

Super

How much you going to sale it for I would like to buy it

Excellent restoration! I love some of your nifty techniques: e.g. electrolysis and filing masking tape at the corners. From my limited experience, meths is better than white spirit for degreasing - it evaporates faster and probably dissolves more oil fractions - but white spirit must have worked sufficiently for that Hammerite. You are very confident with grinding - those bare hands!

👍👍👍

clever bloke. very satisfying 👍

Well that was worth watching your work beautiful restoration of that old beat up lawnmower 🎉🎉🎉🎉

Great video, no waffle or filler just got on with the job, now know how to dismantle mine! Thanks.

Necesitaba hacer una limpieza en mi taladro y me vino de joya este videito muchas gracias 😎

Çok başarısız bir tamirat 1.motora kafanıza göre ağırlık katamazsınız balans yapar 2. Kullandığınız yağ bosch orijinal yağ değil dolayısıyla piston hava yapmayacağı için vuruş performansı düşecektir.

❤

excelente explicito Barcelona Venezuela ,francisco sabino,gracias señor.

nice work! the glass repair was really impressive

Ето не оригинал а подделка

FABIEN FABIEN

Lovely, just lovely.

Good job. It seems you're missing the spring in the handle. There should be a large spring.

سلام ولی دستگاه نفس ندارد کار کند علت فکر کنم ارمیچر نیم سوز است

Era que le des una pintadita al broquero

these drills are indestructible.

Ok

Man I found a Blue Rayleigh stowaway 1975 today Saved it! I’m going to restore it if anyone has any useful tips, that’s would be helpful and maybe where to look for parts I think the seat isn’t original or could be wrong and I need the white handle grips I’ve don’t some looking and digging and ever thing else seems to be original. Thank you And great video I’ll sub, maybe share my restoration do a video. Untill then wish me luck

hey,good restoration but my advice is the left pedal have opposite thread so you mustn't cut the pedal

josss

Looks good but choice of wood not great

Şahaser

What grease do you use ? And what is the difference between yellow one and blue one. Great job btw.

From rusty to shining hammer

Щетки сразу не освободил, переключатель режимов не снял, поршень из цилиндра не достал - так и помыл. Сразу видно, что автор разбирает перфоратор первый раз в своей жизни. Спасибо за смелость!

show

Добрый день.В перфораторе когда достаю цилиндр который ударяет по бойку, то его присасывает обратно.Так и должно быть ?

👏👏👏👏👏👏💯💯💯💯👍👌🇧🇷🇧🇷